Battery Division
  • Introduction of SDPPI Certification in Indonesia
    Certification introduction Indonesian General Administration of resources SDPPI(DirektoratJenderal Sumber Daya dan Perangkat Pos danInformatika) is the regulatory authority for formulating, planning and implementing standardization policies in the field of radio and communication, and has the function of public service .It can issue a license for the radio spectrum, including monitoring the interference and imbalance of the radio frequency spectrum. It is an organization with the ability of wireless / communication testing and certification.。 Wireless communication products entering the Indonesian market must comply with the local technical specifications of Indonesia and pass the type certification and customs inspection of sdppi in Indonesia. The General Administration of post and Telecommunications of Indonesia (DGPT) has imposed a mandatory ban on companies outside Indonesia as holders of type approval since June 2009. Authentication mode 1.Send samples to the local laboratory in Indonesia to arrange testing (The lead time is longer and the cost is relatively preferential) 2.Paperwork method: accept CE reports from overseas Indonesian accredited laboratories for certificate transfer application without sending samples for local testing (short leadtime and relatively high cost) On July 28, 2020, SDPPI issued the extension of paperwork treatment for HKT (referring to mobile phones, laptops and tablets) and non HKT products. The reports issued by overseas accredited laboratories within 6 months from the implementation date of the decree are still acceptable (including 16 overseas accredited laboratories for the latest HKT products and 72 overseas accredited laboratories for non HKT products), The above certification processing methods and the list of overseas accredited laboratories will be constantly adjusted and updated according to Indonesian policies (Indonesian policies are updated frequently)) Certification process Send samples to local test lab for testing 1.Prepare test samples and certification data and submit them to AGC Certification Department and project department (forecast)) 2.The laboratory forecasts the products and sends them to the Certification Department 3.The Certification Department will send the samples to the local laboratory in Indonesia for testing and submit corresponding data 4.After the test is completed and all data are complete, submit it to SDPPI for review, and SDPPI certificate will be issued if it passes the review Paperwork mode 1. Prepare certification materials and accreditation laboratory reports and submit them to the Certification Department 2. If the customer doesn’t have the CE report from the recognized laboratory, Need to arrange a new CE test to outsource the test and issue the new report 3. The certification department shall submit the report and relevant documents to the local cooperation organization in Indonesia 4. Review reports and materials of local cooperative institutions in Indonesia and apply for SDPPI certificate Data list No. Documents Special Note Remark 1 AGC Application Form Customer fill out Necessary for case start 2 POA Fill out, signed and sealed by local importers in Indonesia With reference template 3 Declaration Form Radio Customer fill out With reference template 4 FR.PM.5_Certification Form Customer fill out, sign with stamp With reference template 5 Declaration of Warranty Fill out, signed and sealed by local importers in Indonesia With reference template 6 Technical Specification ---- 7 MoU/Distributor agreement between brand holder and applicant Mou agreement between manufacturer and importer 8 User Manual ----- 9 CE-RF /EMC Test Reports must be issued by a accredited lab.-ISO17025 lab 10 Test Instruction/Test SOP+Test Mode --- Can assist 11 Schematic Diagram --- 12 Block Diagram --- 13 Parts List --- 14 PCB Layout --- 15 Parts Placement --- 16 Other unspecified data By case by organ Labeling requirements The approved products shall be marked with a certification label, and the label size is not clearly required, but only needs to be clearly visible on the body. If the product size is very small, it can be printed on the packing box or instruction manual  The certificate holder must affix the following contents on each certified wireless communication device before trading or use Label location On equipment On the package Lable Yes or No(Only if it cannot be pasted on the device) Yes((Only if it cannot be pasted on the device) QR码 Yes Yes Warning Sign (not required for short distance equipment) Yes Yes Label format: Label template: Location of label and QR code on the certificate: Certificate number and PLG. ID number are available from the certificate Warning Sign: Warning sign statement: it is forbidden for everyone to change the wireless communication equipment to avoid electromagnetic interference to the surrounding environment; Certificate template SDPP Certification summary: Authentication attribute   Compulsory Certification Test unit  Indonesian authority accredited laboratory (AGC forecast) Sample demand ≥2PCS Certification cycle  2-3 weeks (based on CE report of overseas accredited laboratory)   7-9 weeks (local test) Local representative   Actual importer Model control   One certificate with one model Certificate validity  3 Years
    View More
  • Telecommunications business law - JATE
    Definition JATE – Japan Approvals Institute for Telecommunications Equipment(Also called:Japan telecommunications equipment Accreditation Association,RCB number is 001)JATE certification is actually a technical condition compliance certification (Technical Conditions regulatory compliance certifications for telecommunications terminal equipment),Also known as telecommunications business law certification。 JATE is the first registration and certification body recognized by MIC for the compliance certification of technical conditions of telecommunication equipment (RCB, Registered Certification Bodies), Therefore, it is commonly referred to as technical condition compliance certification as JATE certification。The communication equipment connected to the public telecommunications network must meet the technical requirements of the Japanese Telecommunications Law when go to the Japanese market, and complete the compliance certification of technical conditions, i.e. JATE certification。That is, all products connected to public telephone or telecommunication network must apply for JATE certification. In short, JATE certification is the network access certification in Japan. MIC- Japan electrical communication terminal machine Review Association JATE Authentication mode Technical conditions compliance and design compliance certification ①Fixed telephone network terminal (e.g. PBX, telephone) ②Mobile terminals (such as WCDMA / HSPA, LTE / volte and 5th generation mobile phones) ③Internet protocol telephony devices (such as SIP proxy and IP telephony with assigned phone number 0AB-J”)Internet  ④ISDN Terminal equipment (e.g. terminal adapter, digital telephone) ⑤Leased lines and data communication equipment (e.g. Ethernet equipment, mobile data terminal) ⑥Terminal equipment for transmitting radio waves in terminal facilities (e.g. WLAN, Internet of things equipment) (according to Article 9 of the regulations) ⑦Technical standard conformance certification of security standards for Internet of things devices (such as routers and Internet of things devices). Products with Bluetooth SIG certified logo or Wi-Fi Alliance, then no need test. It is indicated in MIC of "terminal equipment certification guide (First Edition) [Japanese] Based on telecommunications business law" issued by mic on April 22, 2019. Public WLAN services must continue to be certified. Technical Requirements Compliance Certification Ensure that the data terminal equipment of the next generation network, leased lines and other telecommunication equipment meet the technical requirements formulated by the telecommunication operators authorized of MIC。              There are two cases of compliance certification for telecommunication terminal equipment: Firstly: For ordinary telephone devices, it's only need to certified with JATE authentication in accordance with the telecommunications law Secondly: For wireless terminal equipment, it's required to certified with JATE authentication  according to the telecommunications law and TELEC authentication according to the radio wave law       JATE Authentication mode JATE Certification procedure JATE Certification label MIC logo and certification number shall be marked on the certified product, which is a 10 digit number composed of numbers and letters               Representative CAB organization code(MICOM: 210, Phoenix: 204) JATE certificate template JATE Certification summary Authentication attribute Compulsory Certification Test Lab AGC Sample Request ≥1 set end product + 1 conduction engineering sample (depending on the product) 测试周期 2 weeks  (depending on the product) 认证周期 5-15 working days 标签和资料说明
    View More
  • Product Safety of Electrical Appliance and Materials-PSE Certification
    An Outline of Regulations of the Electrical Appliance and Material Safety Law In April 2001, The Ministry of Economy, Trade and Industry (METI) formulates Electrical Appliance and Material Safety Law (DENAN) for the purpose of entrusting the state's authority to the private third-party organization. It also aims to regulate the manufacture, sales and export of electrical appliances and materials. And foster voluntary activities to ensure the safety of electrical appliances and materials, so as to protect consumers from hazards caused by the electrical appliances and materials. Definition of Electrical Appliance In Article 2 of Electrical Appliance and Material Safety Law, it specifies the 1st to the 3rd items as Electrical Appliance. 1.Parts of electrical facilities for general use (meaning electrical facilities for general use as prescribed in Article 38, paragraph 1 of the Electricity Utilities Industry Act (Act No. 170 of 1964)) and machines, appliances, and materials used in connection thereto, as specified by a Cabinet Order. Almost all electrical appliances and materials belong to the first category. In short, electrical equipment specified in the electrical safety law refers to electrical equipment connected to 100V or 200V AC commercial power supply in homes, offices (it is not necessary to appoint a licensed Chief Electrical Engineer) or agricultural workplaces. As DC general electric equipment is not actually used at present, DC equipment is not specified. For CD recorder connected with the AC adapter using the connector, the AC adapter (including the connector attached to the AC adapter) belongs to electrical supplies, while the CD recorder host does not belong to electrical appliance. 2.Portable Power Generators Specified by a Cabinet Order It specifies portable power generator with voltage between 30V to 300V. 3.Storage Batteries Specified by a Cabinet Order It specifies a lithium-ion battery whose volume energy density of each single battery reaches a certain value and it is not for a specific purpose. The unit volume energy density of each single battery is more than 400wh / L, and it is not included in products for automobiles, electric bicycles, medical devices and industrial machinery. PSE Certification Classification Two Types of PSE Certification PSE Diamond Certification:"Specified Electrical Products”sepcifies116 items which are more likely to cause injury from product usage like charger or adapter need PSE diamond certification. PSE Circle Certification:“Non-Specified Electrical Products”specifies 341 items with less injury need PSE circle certification. Most of them are household appliances, lighting product, lithium battery, etc. PSE Certification Process PSE Certification Labeling
    View More
  • AGC is Accredited as VCCI Authorized Lab
    AGC is accredited as VCCI Authorized Lab on 20th, June. It includes four authorization capabilities “Radiated emissions above 1GHz”, “AC mains power ports”, “Conducted Emissions at Telecommunication (Wire) ports” and “Radiated Emissions Below 1GHz”. As AGC can issue Japan-approved reports directly, its testing efficiency will be highly improved to reach higher level in testing trade. AGC has taken a big step on providing more efficient VCCI certification services and compliance service for the majority of enterprises. Certificate verification link:  Input “Attestation of Global Compliance“. List of Registered Measurement Facilities | VCCI Council Registration No.:G-20132 (Radiated emissions above 1GHz) Registration No.:C-20098 (AC mains power ports) Registration No.:T-20102 (Conducted Emissions at Telecommunication(Wire)ports) Registration No.:R-20136 (Radiated Emissions Below 1GHz) VCCI is a certification mark of Japanese electromagnetic compatibility certification, which regulated by Voluntary Control Council for Interference by Information Technology Equipment. It is a voluntary certification. VCCI Certification Method Multimedia equipment (MME) products exported to Japan must comply with VCCI-CISPR 32 technical requirements formulated by VCCI committee. Products should have EMI test report issued by VCCI authorized lab. Meanwhile, manufacturers should apply to become a VCCI member (https://www.vcci.jp/membership/join.html) and submit test report to VCCI. The product can only be marked with VCCI mark after test report is approved by VCCI. VCCI Logo Registered product should be marked with VCCI logo or declaration. The VCCI logo must be clear. VCCI Certified Product Range VCCI applicable products Multimedia equipment (MME) sold in Japan includes many products like information technology equipment, audio and video equipment, broadcast receiver equipment, stage lighting control equipment, etc. MME is divided into “Class A Multimedia Equipment” (hereinafter referred to as Class A Equipment) and “Class B Multimedia Equipment” (hereinafter referred to as Class B Equipment) based on usage environment. Class A equipment: Any equipment that meets the requirements of Class A limit (except Class B). Class B equipment: Equipment that meet the requirements of Class B limit. Class B equipment is mainly used in residential environments to provide adequate protection for broadcast services. For example, broadcast receiving equipment is a Class B equipment. VCCI Non Applicable Products MME used in industrial, scientific, medical (ISM), and automotive area is not applicable to VCCI. AGC Test ability AGC is accredited as VCCI authorized lab, it can provide Conducted Emissions and Radiated Emissions test for products. AGC will issue EMI test report and assist client on preparing related document to become a VCCI member and complete product compliance registration. ★Product Category: information technology equipment, audio and video equipment, broadcast receiver equipment, stage lighting control equipment, etc. ★Test Standards: VCCI-CISPR 32 ★Test item: Conducted Emissions at Telecommunication (Wire) ports, Radiated Emissions (1G up, 1G down). ★VCCI Certification Process: 1. Prepare Test samples and certification document  2. Product testing by VCCI accredited lab (AGC). 3. AGC laboratory issues test report + VoC 4. Product compliance registration.
    View More
  • PSE
    Summary Japan PSE is mandatory safety certification, evidence of the electronic electrical products has passed the Japanese electrical product safety act (DENAN Law) or international IEC standard safety standard test. Japan DENAN electrical and electronics products can be divided into two categories: A specific electrical products (specified products), including 116 kinds of products; B non - specified products, including 341 kinds of products. Specific electrical product must be authorized by the Japanese ministry of economy of the third party certification body products and factory test equipment inspection, issuance of PSE certification, certification valid between 3 to 7 years, and labeled with PSE diamond in products. Non specific electrical products is proved by means of self-examination and declare conformity of the product, and labeled with PSE circle on the product. Japan's benchmark electrical product safety technology has two kinds: (1)The province to item 1 benchmark, refers to the domestic technical standards; (2)The province to item 1 benchmark, that is coordinated with the IEC standards. Need to pay attention to, the province has standard item 1 and 2 benchmark is the province that established according to the standard system of independently, to pay attention to not be able to mix these two standards. In the enforcement of rules don't watch the first 2 specifies the name of "electrical appliances", and as stipulated in the electrical products of the "type to distinguish". "Type" refers to the structure, material, or performance, "type to distinguish between" refers to the product safety aspects we confirmed by the structure of the scope of the same nature, material or performance, or a combination of all three. In a wide variety of products type, according to the nature of roughly the same elements and divided into different groups, this is the "type". Therefore, it is important to note that its varieties division and model may not be consistent with enterprise. AGC can be done directly in the domestic circle PSE test and issue a report issued the certificates and the type of table, the test results have been obtained METI's approval. lithium battery PSE On January 18, 2008, the Japanese economy, trade and industry (METI) released the cabinet according to the electrical appliance and material safety law enacted law, a specific range of lithium ion battery has been included in the directory for electrical appliance and material safety products, since November 20, 2008, exports to Japan of the particular range of lithium ion battery, must conform to the requirements of the law about supplier compliance declarations, and listed on the relevant PSE marks must be paste Specific range is: limited to the energy density of not less than 400 wh/L of secondary batteries, batteries, but does not include car with secondary lithium ion batteries, not including electric bike, medical equipment, industrial equipment used in secondary lithium ion battery, also does not include welding way or the battery in the similar way to fix battery installed on the equipment (cannot be easily shift), or those with special structure of the battery. According to the rules, most of the range of lithium batteries used in Mobile devices, such as Mobile Phone, Notebook, etc. These batteries and batteries PSE test standard are: JIS C 8714:2007.
    View More
  • IDA
    Summary Singapore's Infocomm Development Authority (IDA, Infocomm Development Authority of Singapore), the statutory body responsible for information and communication management. http://www.ida.gov.sg/ iDA use and management of telecommunications products, mainly based on technical specifications developed by iDA, who need to sell or telecommunications equipment used in Singapore are required to apply iDA. Application requirements IDA Type RF / Telecom device Authority IDA Certification method SDoC / Certification Local representative request Yes (who has telecommunication dealer’s license) Local testing request No Lead time 2~3 weeks Sample q’ty at least 2 sets Basic Files AGC Application form CE-RF report Related information of the local representative User Manual Product Specification Schematic Diagram Black Diagram BOM PCB Layout & Location External & Internal Photos of EUT Label &Local & Size Remark 1, the certificate is valid for 3 years;  2, the report needs to be qualified;
    View More
  • KCC/MSIP
    Summary The announcement of KCC-2008-108 file on August 7, 2007, the Korea Communications Commission announced (KCC, Korea Communications Commission) to replace the previous South Korean Ministry of Information and Communication (MIC, Ministry of Information and Communication). KCC certification is the mandatory certification for telecommunications equipment and products based in Korea "Telecommunications Basic Law" and "Radio Wave" implementation. Korea Communications Commission is responsible for the management of telecommunications products, which authorized the RRA(Radio Research Agency) for certification bodies, for the implementation of specific product certification. KCC certification is certified by the previous MIC certification accredited laboratory for conformance testing of Korea, issued approval certificate issued by the RRA. KCC was renamed MSIP (Ministry of Science, ICT & Future Planning) according to the latest Korean regulations KCC. KC label The specific content of the new regulations of KCC mark: 1, Begin with MSIP instead of KCC of the KCC certificate / registration number from the original . 2, Starting from 1 July 2,2013, Submission of applications to the NRRA, the system automatically generates MSIP-XXX-XXX-XXXXXXXXXXXXXX form named in the certificate / registration number. 3, Labels which contained KCC-XXX-XXX-XXXXXXXXXXXXXX form naming certificate / registration number of the certificate which had been obtained before July 1st2013, can be used until 30 September 2013. 4, Products shipped to South Korea after October 1st,2013 must use label in the form of MSIP-XXX-XXX-XXXXXXXXXXXXXX. KCC证书号码解析   ①The first four codes are MSIP : Ministry of Science, ICT & Future Planning ②Authentication type  Authentication type Indicating Certification C Registration R Interim I ③Test section Test section Indicating Radio R Telecommunication T Electromagnetic E Mixer M ④Application type  Application type Indicating Manufacture M Import I Sale S ⑤Applicants ID:. Three-digits code consists of English letters or numbers; the first time applicant do not have the Company ID,  which will be generated and permanently represent the applicant after applying for KCC. ⑥Product ID: Self-encoded by the applicants , among which can use letters, numbers or link sign "-", up to 14 digits maximum. KC labeling requirements Product labels can be resized with the product, but the height should not be less than 5mm, unless the product size is very small, such as: storage device, etc ... which can be able to adjust the height. Label Color: basic KC LOGO color is indigo. If there are special reasons for not using Indigo, you can use the following colors (gold, silver, and black). Gold/ Silver can be used with a special glow / shiny printing results, or any monochrome. Application requirements Type ITE device (EMC) Authority RRA Certification method EMC Registration Local representative request No Local testing request Yes Lead time 3~4weeks Sample q’ty at least 1 set Basic Files AGC Application form Korean User Manual Schematic Diagram Black Diagram Type RF &Telecom device Authority RRA Certification method Type approval Local representative request No Local testing request Yes Lead time 4~5weeks ample q’ty at least 2 sets Basic Files AGC Application form Korean User Manual Schematic Diagram Black Diagram PCB Layout & PCB Location BOM/Parts List Business license for application and manufacturer Antenna Specification (Include model name, air line, gain, pointing, characteristic, manufacturer, manufacturing country, partial wave character, radiation pattern, etc.) Channel List Modulation,Nomodulation Program, Operating instructions Test program Safety Approval Authority MIC Local representative request No Local testing request Yes Lead time CB report for 4~5 weeks (excluding work inspection) No CB 5~7 report week (excluding workers) Sample q’ty at least 2 sets Basic Files AGC Application form Korean User Manual Schematic Diagram Black Diagram PCB Layout & PCB Location BOM/Parts List Remark 1, the need for factory audit; 2, the control products are all used for the 50V~1000V and AC power supply of electrical products
    View More
  • SDPPI
    Summary Wireless products exported to Indonesia, must pass the type certification and customs inspection of Indonesia SDPPI.  Indonesia Postal electricity Letter Administration (Directorate General of Post and Telecommunication, DGPT) became mandatory since June 2009, Indonesian ban offshore companies for being type approval holder.  Safety requirements for low-power devices are not mandatory in Indonesia. 2.4 GH and 5 GHz radio certification is a mandatory requirement POSTEL certification.  Application requirements Indonesia certification application, you need to provide a local Indonesian company as a certificate holder who had been authorized by the foreign manufacturer. Indonesia Local companies allow certificate holders as vendors local agents, local wholesale or local brokers. (You need Indonesia local test).  In order to meet the requirement for local companies as certificate holders, local companies need to provide the documents below. File must contain: A.act of association copies (Bahasa Indonesia, "aktapendirian") B.tax number copies (Bahasa Indonesia, "NPWP") C.company registration copies (Bahasa Indonesia, "TDP") D.import license copies (Bahasa Indonesia, "NPIK") In addition, you need to provide relevant technical information and application forms as well as providing information on local agents (certificate only distributed to local dealers) SDPPI Authority DGPT Local representative request Yes Local testing request Yes Lead time 6~8 weeks Sample quantity At least 2 sets Basic Files AGC Application form User Manual Schematic Diagram Black Diagram PCB Layout & PCB Location Power of Attorney Other specified documents Remark Starting in September 1, 2014 SDPPI certificate no longer A certificate and B certificate 1.no longer A certificate and B certificate; 2.Manufacturers or importers can directly apply for SDPPI certificates; 3.The certificate is valid for three years, but can only be extended for three years. Six years later, the certificate needs to be postponed, only a new application. 4.Since November 14, 2014, all of the products with BT and WLAN function must provide direct measurement of the prototype, the policy has been canceled for the Bluetooth products can accept the normal prototype.
    View More
  • WPC
    Summary India Wireless Planning and Coordination Bureau on behalf of the Department of Telecommunications in India to issue form accreditation for import and sale of radio equipment in the Indian market.  Wireless products exported to India need to do WPC (Wireless Planning & Coordination Wing) Certification. Application requirements WPC (RF) Local representative request Yes Local testing request No, CE reports Lead time 6~8 weeks Sample q’ty N/A Basic Files AGC Application form Power of Attorney Other specified documents Remark 针对无线发射类产品 TEC (Telecom Engineering Center) Authority Telecom Engineering Center Local representative request Yes Local testing request Yes Lead time 8 weeks Sample q’ty At least 4 sets Basic Files AGC Application form Power of Attorney Other specified documents Remark Only Telecom terminal products
    View More
  • SIRIM
    Summary SIRIM is the only certification authority of Malaysia, electrical and electronic products exported to Malaysia are required to apply for recognition of SIRIM Cert. In principle, the applicants should be Malaysian local institutions. SIRIM certification application and management is charged by SIRIM QAS. Malaysia imposed compulsory product certification system is divided into two kinds of certification and voluntary certification. Communications equipment and "Electrical Equipment approve Article Example "set forth in 31 categories of electrical products subject to mandatory type certification and safety certification, respectively. Other products are in the Voluntary certification category. At present, for electromagnetic compatibility, there are not mandatory requirements in Malaysia. SIRIM Mark Malaysia has a lot of different kinds of products to meet the requirements of CB IECEE system. MS marks and ST marks are the voluntary and compulsory safety signs of the products exported to Malaysia. Application requirements IRIM (RF/Telecom device) Authority SIRIM Certification method Type approval Local representative request Yes  Local testing request Yes Lead time 8weeks Sample q’ty at least 2 sets Basic Files AGC  Application form User Manual Schematic Diagram Black Diagram PCB Layout & PCB Location RF module’s SPEC CE-RF+EMC+Safety reports Remark 1, Samples are not able to be delivered until the import permit is released to the local rep. 2, Labels must be purchased from SIRIM. 3, Only the certificate holder could import shipment and purchase labels from SIRIM, so each importer must have their own certificate.
    View More
  • VCCI Certification
    Summary VCCI is a symbol of Japan's electromagnetic compatibility,which is controlled by Voluntary Control Council for Interference by Information Technology Equipment.According to CISPR 22 assessment of information technology products are in compliance with VCCI requirements.VCCI certification is not mandatory,But selling information technology products in Japan , generally will be required for VCCI certification.Manufacturers should first apply to become a member of VCCI,then they can use VCCI symbol.In order to obtain the approval of VCCI, the EMI test report provided must be issued by VCCI registration approved testing agency. Application requirements EMC Approval Authority VCCI Local representative request No Local testing request No Lead Time 1~2 weeks Sample q’ty At least 1 sets Basic Files AGC application form User manual 产品规格书 Circuit diagram Black Diagram BOM list PCB Layout / PCB Location Remark 1, Voluntary certification 2, Applicants should become a member of VCCI
    View More
  • JATE
    What is JATE Certification? Ministry of Public Management, Home Affairs, Posts and Telecommunications (MPHPT) enacted Telecommunications Business Law in 1984, stipulated telecommunication equipment manufactured and sold in Japan must be certified compulsory. JATE(Japan Approvals Institute for Telecommunications Equipment)is the main authority for technology compliance certification of telecommunications equipment in Japan. In conclude, JATE is the compulsory certification for product sold in Japan. Applicable product range JATE Certification apply to all telecommunication equipment connected directly with public phone or wireless network, such as wireless calling equipment, ISDN equipment, leased line equipment and other telecommunication equipment. Note: Blue Tooth product is no longer under management and control. Slave WIFI equipment is no longer under management and control. (Equipment connected to telecommunication network through router, such as WIFI camera) Two Testing Mode of JATE Certification Technical Conditions Compliance Certification Compliance certification of technical conditions includes type approval and stand-alone certification. The compliance certification ensures telephone network, wireless calling equipment, ISDN equipment and leased line equipment comply with technical requirement specified by MPHPT.(Related regulation of terminal equipment) Technical Requirements Compliance Certification Compliance certification of technical requirements includes type approval and stand-alone certification. Compliance certification of technical requirements ensures wireless calling equipment, leased line equipment and other telecommunications equipment comply with certain technical requirement formulated by telecommunication operators authorized by MPHPT. Application Material: 1.Application form 2.Schematic diagram 3.PCB layout 4.BOM 5.Specification 6.Number map 7 ISO certificate 8.Other document Certification Logo and Certification Number X YY AAAA BBB Device code Year Serial number Institution code LOGO Note: Certification mark and the certification number should appear on the same line. The minimum size of logo diameter is 5mm. (If the product volume is no more than 100cm³, then minimum size of the logo diameter will be 3mm ). The logo can be combined with TELEC Logo for printing. Testing content 1. Basic functions. 2. Calling functions. 3. Transmission timing. 4. Random access control. 5. Time alignment control. 6. Location registration control. 7. Information switching function. 8. Functions of receiving level reports. 9. Functions of stopping transmission according to instruction. 10. Function of automatically suspend transmission when the receiving level degraded. 11. Function of automatically suspend transmission. 12. Function of ensuring important communication. Other Information Whether compulsory: compulsory certification Certificate Validity period : It is permanently valid on condition that nothing has been changed in the design and application standard. Factory audit requirement:no requirement Certificate holder requirements: no requirement Technical information: voltage frequency AC 100V / 200V, 50Hz / 60Hz, plug JIS 8303 Sample quantity: more than 2 sets Certification lead time:about one month AGC Certificate of Acceptance AGC keeps a long-term cooperative relationship with JATE and possesses professional testing labs & technical teams, which can help enterprise break into Japanese market efficiently.
    View More
1 2 >>

A total of 2 pages

welcome to AGC
If you have any problem when using the website or our products, please write down your comments or suggestions, we will answer your questions as soon as possible!Thank you for your attention!

home

services

about

contact